The CD-ROM drive does not work after you install it. 1) make sure the drive ribbon cable is connected so that the colored stripe edge is lined up with pin one At a DOS prompt, type A:CDFT and press Enter. 3. From your findings Are you suggesting that I should attach this converted dvd to port sata 1 and not 0 for it to workregardsany advice welcome Flag Permalink This was helpful If you receive any messages stating that Windows is installing new hardware, wait until the process is finished, and the see if the CD/DVD drive is available now. http://meocloud.net/windows-10/cd-rom-problem-still-not-fixed.php
SMARTDRV 5.0: If you have SMARTDRV 5.0 with MS-DOS 6.2 or PC-DOS 6.3, you might have problems reading multisession CDs such as Kodak Photo CD. Audio Adapters Many audio adapters default to IRQ 7. Remove the CD-ROM from adapter and connect to DVD burner. All Rights Reserved Tom's Hardware Guide ™ Ad choices Techadvice.comMain, Tech Info, Glossary, Companies, Hardware. http://www.pcguide.com/ts/x/comp/cd/recogDriver-c.html
Windows 10 Cd Drive Not Working
Here's exactly what you need to do to reset the computer power: Press and hold the power button for 5 seconds to turn your computer completely off. Sound Cards CD-ROM, Sound Card, Connectors In order for the computer to be able to play sound through the CD-ROM drive a cable needs to be connected from the "Audio Out" Click Here to Start Download 2. Remove the DVD burner from adapter and connect to IDE HDD (WD800JB) and viola, it works!!8).
This will cause the CD-ROM drive not to be found within Windows 95. If you are using Windows 9x, ME, 2000, or XP it is likely that if the drive is properly installed that it will be automatically detected and installed when the computer The shiny surface (on the back of the disk where there is NO writing) has to be completely clean. Unable To Burn Cd In Windows 10 In addition, if you attach anything to the secondary IDE controller the USB will automatically move to another IRQ to prevent an actual conflict.
Trying to do a clean install of windows xp but system wont boot from cd i get er solved Installing Windows 7 on second HDD (on IDE to SATA adapter - Look for the place where you can set the Boot Priority Sequence. Verify that the IDE device is setup as Auto or CD Drive. Also please exercise your best judgment when posting in the forums--revealing personal information such as your e-mail address, telephone number, and address is not recommended.
Watch out for 32-bit disk access being enabled under Windows 3.x. Windows 10 Cd Burner Not Working If the CD-ROM is on the end of the chain then make the termination active. Editor's note - quite often, these issues are being caused by the hardware itself, so what we could recommend you is to try and have a look a this list of Additional information How to install computer hardware.
Windows 10 Cd Drive Not Showing Up
If there is already another device such as a hard drive connected, then that device would already be configured as the Master and you will need to set the CD-ROM drive This may cause problems with CD-ROM drives on the ATAPI/IDE interface. Windows 10 Cd Drive Not Working Give me some tips. Windows 10 Dvd Drive Not Reading Discs How to determine the CD drive type How do I find what CD or other disc drive I have?
Each IDE controller can only have one Master and one Slave device. this content This can manifest as a driver error when the operating system tries to access the driver in question. Software setup IDE/EIDE CD-ROM drives only require the one or two CD-ROM drives for the drives to work. There is also the risk of installing the wrong driver and causing other problems in addition to the existing ones. Can't Burn Cd Windows 10
Ask ! Using a text editor, add a /U parameter after the SMARTDRV statement (for example, SMARTDRV /U). Select the link that corresponds to your system's operating system. - DOS/Microsoft Windows 3.x - Microsoft Windows 95/Windows NT - OS/2 and OS/2 Warp V. weblink Or time to buy a new dvd rom?
You can also buy cleaning kits at retail outlets. 2) The read head inside the drive can get dirty. Windows 10 Won't Read Cd This will mean you cannot access the CD-ROM under DOS any more, but there is a workaround: creating a custom boot profile for DOS programs. from many post on internet only yours help.
The jumpers should be set correctly.
Kozierok.All Rights Reserved. Sometimes the possible settings are either "Master" or "Master with a Slave". Not responsible for any loss resulting from the use of this site. There Was A Problem Burning This Disc Windows 10 No other SCSI device on the system can use the devices SCSI ID.
Thank you… Reply driversHelp says October 14, 2014 at 7:30 am if you are having trouble opening the cd tray then you can try accessing it from another program (such as mere laptop ka CD-Rom eject hone ke baad ab under jaker fix nhi ho rha , aur o banar aaja rha hai iske liye mujhe solution btaye. The ribbon cable should be inserted properly and pin 1 on the drive should be matched up with pin 1 on the interface controller or motherboard. check over here The jumpers are not properly configured Every IDE device has to be configured as either a Master or a Slave.
If you suspect this, remove the following statement from the CONFIG.SYS file: DEVICE=SMARTDRV.EXE SMARTDRV 4.0: If your IDE CD-ROM drive is configured as a slave device, SMARTDRV 4.0 might intermittently suspend Once you've set it as you wish, use the proper keys to Save and Exit from here, and the settings will be saved and the machine will reboot.When set this way, Finally, connect the Molex style power cable to the back of the CD-ROM drive. But, if you're not sure how to do that, ask someone who does, or simply ask a service for help.
© Copyright 2017 meocloud.net. All rights reserved.