CD-ROM Drive-where To I Put The Pin Thingys For Master / Slave?
Click next and soon the new drive is available. Advertisement On the motherboard end, the socket looks like this. Figure 8-1: Removing an RF shield before installing the drive Basic Versus Enhanced OperationATAPI optical drives require no special configuration steps to function at a basic level. After you replace the side and/or top panels and the drive bezel, the system is ready to go. navigate here
In order to use Cable Select jumpering, several conditions must be met. Protect the drive from static discharge by wearing a grounded wrist strap. See our CD-ROM and DVD definitions for further information and related links. Have the drive as master can help prevent a buffer underrun when creating a CD. https://forums.techguy.org/threads/cd-rom-drive-where-to-i-put-the-pin-thingys-for-master-slave.151997/
Master Slave Hard Drive Jumper Settings
A Cable Select cable can be used with master/slave drive jumpering. There should be three lines visible, assuming that two ATA channels are installed and enabled. Reply Shayan November 18, 2015 at 6:19 pm what to do if i use 2 IDE hard disk instead of a CD-ROM? In the menu, look for an option named Auto Detect or something similar, if the BIOS doesn't automatically show your drives.
Now figure out where your additional drive is going to go. After the drive is secured then go ahead and connect the power and IDE cables. If you're dual booting then Fat32 would probably be a good idea if the other OS can't read NTFS. How To Connect Two Hard Disk In One Pc The Master for 40-wire cables goes on the the Middle connector.
There is a connector at each end of the cable and another one about two-thirds of the distance from the motherboard connector. What Is A Slave Hard Drive The three connectors are typically different colors and attach to specific items: The blue connector attaches to the motherboard. There is a notch on one side of the connector to prevent you plugging it in the wrong way, so make sure you align that. http://www.techrepublic.com/forums/discussions/setting-up-primary-and-secondary-dvd-plus-rw-cd-rom-drives/ Now, it's time to do the same for electronics.
All Ultra ATA/66 devices should be attached to a single channel and devices that do not support Ultra ATA/66 should be connected to a separate channel. How To Connect Two Sata Hard Disk In One Pc Move it back to its original location, reconnect all the external cables, and power it up. My old computer died but its IDE drive was perfectly fine so it seemed obvious to me to install the old IDE drive into my new computer as a second drive. Most modern CD drives are ATA33 while the modern hard drives are ATA133.
What Is A Slave Hard Drive
Is the full capacity of the hard drive being seen: Verify the BIOS has auto-detected and LBA mode is enabled. http://www.pcadvisor.co.uk/how-to/pc-upgrades/how-slave-sata-drive-3461780/ Newer Than: Search this thread only Search this forum only Display results as threads Useful Searches Recent Posts More... Master Slave Hard Drive Jumper Settings During a fresh install, Windows XP tests the ATA interfaces and the connected devices to determine DMA compatibility. Ide Hard Drive Jumper Settings Need more storage space?
wire 28 can be checked for continuity. http://meocloud.net/hard-drive/changing-master-hdd-from-sata-to-pata.php Generally it's the [del] button that gets you into the BIOS but sometimes it's F1 or F2. Additional information How to install computer hardware. Once you accept the changes, the new drive letter takes effect immediately. How To Slave A Sata Hard Drive
If you are upgrading an existing drive or replacing a failed drive, it might seem reasonable to configure the new drive the same way the old drive was configured. If Your Computer No Longer Works, How Do You Know It Was Your Hard Drive That Failed? Look on the bottom right and you'll see something that looks like this picture. The Digital Right to Repair Bill requires manufacturers to provide owners and independent repair businesses with fair access to service information, security updates, and replacement parts.
Sure enough, the BIOS shows two devices loaded and functional.
This cable has one side of the cable that is red or blue indicating PIN 1. For the CD-ROM, the diagram indicates that 2 is Slave setting. Both drives on a channel must support CSEL, both drives must be jumpered as CSEL, a CSEL cable must be used, and the host interface connector must support CSEL. Seagate Ide Hard Drive Jumper Settings When your stuff breaks, they want to be the only people allowed to fix it.
However, one of the gaps between the end connectors and the middle connector is longer – this is the end that plugs into your motherboard. That way, you can easily boot from a CD or DVD without altering the BIOS settings, but it might add a few seconds to the boot time while the optical drive The cable length will affect your choice too, as IDE cables are usually quite short. weblink Set The Jumpers & Plug In Since I only have a single IDE CD-ROM and single hard disk to show you today (as well as only a single physical IDE connector
For more information, including step-by-step instructions, see: Install an extra hard disk in your PC and How to install an SSD in your PC Tags: PC Upgrades Share this article Share It’s yours. Right click on it. Advice from Jim Cooley Reinstalling or updating the chipset drivers may also enable (or re-enable) DMA support for the optical drive under Windows 2000 or XP.
The master can also be referred to as the "primary" drive with the slave being the "secondary". A drive can only transfer as fast as the slowest device on the channel. More about Optical Drives[/quote] One Comment Add Comment If the system ha 2 PATA optical Drives and one SATA Hard drive? Configure the optical drive as the secondary slave.If the system has one PATA hard drive, configured as the primary master, and two ATAPI optical drives, for example, a DVD-ROM drive and
Frequently Asked Questions: Can I connect a older ATA33 drive with my newer ATA66/100/133 drive? It requires manufacturers to provide owners and independent repair shops with access to repair information and replacement parts—so you have the resources you need to fix things quickly and affordably. Use a file to grind down any sharp burrs that remain, ensuring that no filings remain inside the case on the motherboard where they can cause havoc. Troubleshooting Additional computer CD-ROM help and support.
Locate the motherboard ATA interface connector you plan to use (usually the Secondary ATA interface). BUY NOW FREE TRIAL PARTNERS Partners Become a Partner Locate a Reseller Partner Programs > How to > Computer Instruction > Install IDE Hard Drive Install IDE Hard Drive 2016-08-05 No, create an account now.
© Copyright 2017 meocloud.net. All rights reserved.