Cd Rom & Soundcard Issues :(
This has happened to us on many different systems, using different motherboards and sound cards. The CD-ROM that was installed was proprietary and connected to the sound card, and the Hitachi CDR-8330 CD-ROM I got to replace it is detected by the system and reads CDs, To share a drive over a network in Windows for workgroups (WFWG) you must add the switch (option) /s after the device file entry "MSCDEX" in the autoexec.bat file. It'd be easier to get an old IDE CD-ROM drive and use that instead. navigate here
See our CD-ROM and DVD definitions for further information and related links. Lastly, the two errors I mentioned regarding the sound were : The Audio 16 hardware is not responding. If this does not work, view the directory (DIR A:
How To Connect Cd Rom To Motherboard
Perhaps the most common is the sound card itself. Also, programs such as EZ SCSI by Adaptec, can report what IDs the devices use, and finally you can look at the jumpers of the other devices in your system and If you've got any elderly gear with tarnished pins on its mains or audio plugs, you may even find the noise level alters after unplugging it and plugging it back in I've experienced a lot of ground-loop problems in such situations, and suspect the problem's worse than with a PCI card, because the external interface is in the middle of a large
Some SCSI controllers will report this information while the computer is booting. This will open the CD-ROM section and show you the drive name that windows has detected. Sadly, some laptop switched-mode power supplies seem to add digital noises to your audio even when you're using an external interface. Conventional Memory Is The First ---k? Most of the later 16 bit sound cards such as the sb16 https://en.wikipedia.org/wiki/Sound_Blaster#/media/File:SB16-CT2940.JPG have a suitable connector.
Once connected, turn on the computer and enter CMOS setup. How To Connect Dvd Drive To Motherboard Sata Additional computer CD-R help and support. Some sound cards, for example, have problems with motherboards with certain Via chipsets, while other sound cards have problems with AMD K6-family CPUs when used with certain AGP video cards.Remove the Attach cables The CD-ROM should have two cables connected to it and may have an audio cable, which is the smallest of the cables, the CD-ROM audio cable (or sound card
Cd Drive Cable Connection In Cpu
Usually if that happens you have both drives as master, you can usually change that with jumpers on the back of the drive. http://www.techadvice.com/tech/C/CDROM_TS.htm Power Supplies26.1 Power Supply Characteristics26.2 Volts, Amps, Watts, and Regulation26.3 Power Connectors26.4 Choosing a Power Supply26.5 Installing a Power Supply26.6 Troubleshooting Power Supplies26.7 Our PicksChapter 27. How To Connect Cd Rom To Motherboard To make it short - tldr: - Your sound card gives errors on boot. How To Connect Cd Drive To Pc Laptop PSUs only output a fairly low (and therefore safer) voltage, but it's still theoretically possible for an internal fault to cause lethal voltages to appear at the output and to
The shiny surface (on the back of the disk where there is NO writing) has to be completely clean. If you have an IDE one, then ignore me. Retail stores also sell cables with multiple connectors on each end making it easier to match the connector to the device. If this is the only device connected to the controller, then you will set the drive as a Master. Cd Drive Internal Or External
Unplugging one signal or earth lead may cause the problem to get better or worse, depending on how it affects the others. For Desktops... 1) Make sure the disk is centered in the drive's tray. 2) Also check to the autoexec.bat file. The drive will be given the next available drive letter. http://meocloud.net/cd-rom/cdrom-and-burner-issues.php If you have more than one sound card installed, verify that the default playback device is the sound card to which the speakers are connected.If your sound card includes a testing
CD-ROM Drives10.1 Compact Disc Fundamentals10.2 CD-ROM Drive Performance10.3 Choosing a CD-ROM Drive10.4 Installing and Configuring a CD-ROM Drive10.5 Cleaning a CD-ROM Drive10.6 Our PicksChapter 11. Cd Rom Cable Sound card problems that occur when you install a new sound card (or when you add or reconfigure other system components) are usually caused by resource conflicts or driver problems. If the "old" drive is actually a proper IDE CD-ROM and giving HDD errors on boot a common problem could also be the master/slave settings.
The "audio cable" that connects a CD-ROM to a sound card simply ensures that when you listen to audio CDs you can output the sound through the sound card instead of
If you have a set of headphones, connect them directly to Line-out on the sound card to isolate the problem to the system itself. You can also buy cleaning kits at retail outlets. 2) The read head inside the drive can get dirty. The CD-ROM drive does not work after you install it. 1) make sure the drive ribbon cable is connected so that the colored stripe edge is lined up with pin one Can Dvds Be Used In Cd Devices I don't think GiGaBiTe realized it was standard IDE/ATAPI already.
It wasn't uncommon for early sound cards to have 3 or 4 different CD-ROM connectors for different drives like Sony, Panasonic and Matsushita in addition to an IDE connector. Another possible cause is that some video card drivers are optimized for benchmark tests by having them keep control of the bus. Don't rule out digital problems being caused by ground loops either. Next, connect the 40-pin IDE/EIDE interface cable (large gray ribbon cable) to the back of the CD-ROM drive.
Fundamentals1.1 PCs Defined1.2 PC Components and Technologies1.3 System Resources1.4 Building or Buying a PC1.5 Upgrading a PC1.6 Smart Buying Practices1.7 Things to Do with Old PCsChapter 2. Roughly in order of decreasing probability, the most likely causes and solutions are: The Windows audio balance control is set fully in one direction. Older and inexpensive sound cards often have poor audio quality, particularly FM synthesis models. If the CD-ROM is on the end of the chain then make the termination active.
E. For example, if this drive is being attached to the same cable as your hard drive, the CD-ROM drive needs to be set to Slave and the hard drive needs to If you have a choice, locate a sound card as far as possible from other expansion cards. If you do not have the necessary cable, you can temporarily fix the problem by connecting a standard stereo audio cable from the headphone jack on the front of the CD-ROM
Software. If you are running Windows 95/98/2000, OS type should be set to PnP Compatible (or similar words); if you are running NT4, it should be set to Non-PnP OS.Use the procedures October 2015 Latest Videos Trident Audio Developments DECA 500 - NAMM 2017 Uploaded 1 week 5 days ago Soundelux USA U99 - NAMM 2017 Uploaded 1 week 5 days ago Maag The CD-ROM originally installed and attached to the sound card would just result in the computer giving a Hard Drive Controller error and refusing to boot.
If you need a cable make sure you get one that is made for both the CD-ROM drive and the sound card. Some of Apple's dual-processor G5 machines, for instance, have suffered from audio noises that have been tracked down to their power supplies — they happen when the processor switches between its The audio cable will connect to one of the following locations: sound card, motherboard (when onboard sound present), or DVD decoder card.
© Copyright 2017 meocloud.net. All rights reserved.